Design and Ergonomic Evaluation of an Automated Wheelchair Lifting Aid for Caregiver Injury Prevention

Authors

  • Wawan Yudiantyo Universitas Kristen Maranatha, Indonesia
  • Andrijanto Andrijanto Universitas Kristen Maranatha, Indonesia
  • Christina Wirawan Universitas Kristen Maranatha, Indonesia

DOI:

https://doi.org/10.59261/jequi.v8i6.481

Keywords:

Assistive Lifting Device, Caregiver Safety, Ergonomics, Musculoskeletal Disorder Prevention, Wheelchair Transport

Abstract

Background: Manual handling during wheelchair loading and unloading imposes substantial biomechanical demands on caregivers, potentially contributing to work-related musculoskeletal disorders (WMSDs) because of non-neutral working postures and increased spinal loading, particularly at the L5/S1 lumbosacral junction.

Objective: This study proposes the design, development, and ergonomic evaluation of an electromechanical assistive lifting device integrated into the cargo compartment of a Toyota Avanza multipurpose vehicle (MPV).

Methods: A 12-V DC electric winch equipped with a swiveling boom arm and a quick-release sling harness was evaluated during caregiver-assisted wheelchair loading and unloading tasks involving three wheelchair configurations: a standard manual wheelchair (17 kg), a Type A powered wheelchair, and a Type B powered wheelchair (weighing up to 28 kg). Functional compatibility and observable caregiver working postures were assessed before and after device implementation.

Results: Automated lifting system successfully demonstrated proof-of-concept operation with all three wheelchair configurations. Compared with manual handling, assisted loading reduced the need for non-neutral caregiver postures, including approximately 30° of backward trunk extension and approximately 75° of asymmetric lower-extremity bracing. By replacing manual lifting effort with electromechanical assistance, the device enabled the caregiver to maintain a more upright working posture during the demonstrated operations. However, repeated trial counts were not documented; therefore, no statistical success rate or quantified reduction in biomechanical loading can be established.

Conclusion:  Proof-of-concept device demonstrated functional feasibility and the potential to reduce non-neutral caregiver postures during wheelchair loading and unloading. Its integration into the vehicle cargo compartment offers a practical retrofit concept for assisted wheelchair transportation.

Downloads

Download data is not yet available.

References

Abd Rahman, M. N. asrull, Abdul Rani, M. R. ebi, & Rohani, J. M. ohd. (2011). WERA: an observational tool develop to investigate the physical risk factor associated with WMSDs. Journal of Human Ergology, 40(1–2).

Batan, I. M. L. (2007). Pengembangan kursi roda sebagai upaya peningkatan ruang gerak penderita cacat kaki. Jurnal Teknik Industri, 8(2), 97–105. https://doi.org/10.9744/jti.8.2.97-105

Bertocci, G., Manary, M., & Ha, D. (2001). Wheelchairs used as motor vehicle seats: seat loading in frontal impact sled testing. Medical Engineering & Physics, 23(10), 679–685. https://doi.org/10.1016/S1350-4533(01)00102-3

Hart, M. A. (2012). The Lean Startup: How Today’s Entrepreneurs Use Continuous Innovation to Create Radically Successful BusinessesEricRies. New York: Crown Business, 2011. 320 pages. US$26.00. Journal of Product Innovation Management, 29(3), 508–509. https://doi.org/10.1111/j.1540-5885.2012.00920_2.x

Haubert, L. L., Mulroy, S. J., Hatchett, P. E., Eberly, V. J., Maneekobkunwong, S., Gronley, J. K., & Requejo, P. S. (2015). Car Transfer and Wheelchair Loading Techniques in Independent Drivers with Paraplegia. Frontiers in Bioengineering and Biotechnology, 3. https://doi.org/10.3389/fbioe.2015.00139

Hryciów, Z. (2022). The safety of wheelchair occupants in motor vehicles. The Archives of Automotive Engineering – Archiwum Motoryzacji, 97(3), 5–13. https://doi.org/10.14669/AM/155001

Iridiastadi., H., & Yassierli. (2014). Ergonomi Suatu Pengantar. In Bandung: PT. Remaja Rosdakarya.

Joint Committee on Mobility for Disabled People. (1997). Travelling in vehicles while in a wheelchair. Physiotherapy, 83(6), 305. https://doi.org/10.1016/S0031-9406(05)66180-9

Klein, L. J. (1985). Rooftop Manual Wheelchair Loading Device for Passenger Cars. Passenger Car Meeting.

Madej, A., Sawicz, J., Wieczorek, B., Warguła, L., & Kolev, Z. (2023). Mechanism for loading wheelchairs in the car – a review of technical solutions and a new concept. MATERIAL AND MECHANICAL ENGINEERING TECHNOLOGY. https://doi.org/10.52209/2706-977X_2023_2_19

Miyawaki, K., Moriyawa, Y., & SATO, T. (2012). 125 Evaluation of wheelchair lifts for use with motor vehicles. The Proceedings of the Tecnology and Society Conference, 2012(0), 49–50. https://doi.org/10.1299/jsmetsd.2012.49

Nurmianto, E. (1996). Ergonomi Konsep Dasar Perancangan dan Aplikasinya. Pengukuran Dan Perencanaan Sietem Kerja(Antropometri Dan Desain Produk), 3(1).

Pahl, G., Beitz, W., Feldhusen, J., & Grote, K.-H. (2007). Engineering Design. Springer London. https://doi.org/10.1007/978-1-84628-319-2

Rahman, M. Z. U., Ali, I., Ishfaque, A., Riaz, M. T., Ahmad, N., Al Mahmud, M. M. S., & Tanveer, R. (2023). Design, Analysis, and Control of Biomedical Healthcare Modular Wheelchair with Posture Transformation. Complexity, 2023, 1–13. https://doi.org/10.1155/2023/7310265

Sinyukov, D. A., Troy, K. L., Bowers, M. P., Padir, T., & Popovic, M. B. (2025). Wheelchairs and other mobility assistance. In Biomechatronics (pp. 421–468). Elsevier. https://doi.org/10.1016/B978-0-443-13862-1.00005-9

Stanton, N. A. (2018). Handbook of Human Factors and Ergonomics Methods. CRC Press.

Sydor, M., Wieczorek, M., Hitka, M., & Gejdoš, M. (2023). Experimental Study of Persons with Disability, Wheelchairs, and Car Interaction. Systemy Logistyczne Wojsk, 59(2), 263–286. https://doi.org/10.37055/slw/186378

Tang, R., Holland, M., Milbauer, M., Olson, E., Skora, J., Kapellusch, J. M., & Garg, A. (2018). Biomechanical Evaluations of Bed-to-Wheelchair Transfer: Gait Belt Versus Walking Belt. Workplace Health & Safety, 66(8), 384–392. https://doi.org/10.1177/2165079917749862

Ulrich, K. T. , S. D. E. and M. C. Y. (2008). Product design and development. Boston: McGraw-Hill higher education.

Wickens, C. D. (2004). An introduction to human factors engineering. Upper Saddle River, NJ: Pearson Prentice Hall.

Widinarsih, D. (2019). Penyandang disabilitas di indonesia: perkembangan istilah dan definisi. Jurnal Ilmu Kesejahteraan Sosial, 20(2). https://doi.org/10.7454/jurnalkessos.v20i2.1074

Yudiantyo, W. (2020). Perancangan Ergonomis Pegangan Pendorong Kursi Roda Untuk Meninimasi Kesakitan Pergelangan Tangan. Journal of Integrated System, 3(1), 40–48. https://doi.org/10.28932/jis.v3i1.2489

Yudiantyo, W., Sarvia, E., & Andrian, K. (2021). Usulan Posisi Tongkat Dan Penambahan Fasilitas Tambahan Untuk Penyimpan Tongkat Pada Kursi Roda Berdasarkan Pendekatan Ergonomi. Jurnal Sains, Teknologi Dan Industri, 18(1), 104. https://doi.org/10.24014/sitekin.v18i1.11682

Downloads

Published

2026-11-13